Skip to content

Cold-formed C and Z members — EN 1993-1-3

Cold-formed C and Z members and purlins to EN 1993-1-3 — the effective section, cross-section and member resistance, purlins held by sheeting, and what is left to you.

Design checks 10 min read

The en1993-1-3.member-resistance module verifies a cold-formed C or Z member to EN 1993-1-3:2006 with AC:2009:

  • the effective section of §5.5, local and distortional buckling included;
  • cross-section resistance, §6.1;
  • member buckling, §6.2;
  • a purlin held by sheeting, §10.1, on a single span or continuous over its supports.

The module is in New check under EN 1993-1-3, and counts towards the plan's design checks per project.

Scope

CoveredNot verified, with a message
SectionA Cold-formed C / Z section from the section editor: a C or a Z, plain or with lipsAny other section, a catalogue or drawn channel included. A section outside the limits of Table 5.1, which EN 1993-1-3 leaves to design by testing
MaterialCarbon steelStainless steel, which goes to EN 1993-1-4
A COn its own, or as a purlin held by sheeting—
A ZAs a purlin held by sheeting onlyA Z with no sheeting stated: its principal axes lean off its web, so a moment about the web bends it about both, and EN 1993-1-3 reads that only for a sheeted purlin, §10

The section

In the section editor, Cold-formed C / Z takes the depth , the flange width , the lip (0 for a plain section), the nominal thickness and the bend radius : outer dimensions over the nominal thickness, as the makers' tables give them. The section's stiffness comes from its real outline with the bends rounded, as §5.1(3) asks.

The check works on the steel core, mm, the zinc of a Z275 coating on both faces, (3.3c) and the NOTE to §3.2.4(3). A core thickness outside the 0.45 to 15 mm of §3.2.4(1) is said on the result. The material gives the basic yield strength as its , and needs .

The effective section, §5.5

Flat widths are measured on the centreline with sharp corners, Figure 5.1, as every printed example computes:

  • Local buckling of each flat part by EN 1993-1-5 §4.4: the web, a plain flange as an outstand, the lip.
  • Distortional buckling of a lipped flange in compression, §5.5.3.2: the flange and lip are an edge stiffener on a spring, Step 1 for the effective widths, Step 2 for the spring , and , and Step 3 iterated until settles. is held at its Step 2 value through the iteration, as all three printed iterations do. The reduced thickness then applies to the stiffener.
  • The web in bending takes from the effective compression flange and the gross web, in one pass, §5.5.2(3).
  • Rounded corners count by (5.1) where or : and , and the result gives .
  • A lip shorter than is ignored, §5.2(2), and the flange reads as an outstand.

The effective section is formed for compression and for each sense of , so a sagging and a hogging moment each have their own .

Refused, with the ratio and the limit: a flange past 60 with a lip or 50 without, a lip past 50, a web past 500 (Table 5.1), a lip past 0.6 (5.2a), and a bend radius past , where §5.1(6) asks for tests.

What the check reads

On the check:

SettingDefaultWhat it is
, 1.00§2(3); set by the project's national annex as on the other steel checks. also applies to a web under a local force
Formed byPress braking in (3.1) for the average yield strength : 7 for roll forming, 5 for press braking. Unstated, the lower
Webs at supportsNot stiffenedCleats at the supports keeps past = 1.40 in Table 6.1

Per member, under Settings per member: , , and as on the EN 1993-1-1 check; for the web under a local force, the stiff bearing length , the end distance , how supports reach the member (Supports) and how other members do (Members framing in); and, for a purlin, the sheeting:

SettingDefaultWhat it is
Sheeting onnoneThe flange trapezoidal sheeting is fastened to, top or bottom. Stated, the member is a purlin by §10
Sheeting SnoneThe sheeting's shear stiffness for this purlin, (10.1b), 0.2 of it if fixed at every second rib
noneThe rotational restraint the sheeting gives the purlin, per metre and radian, §10.1.5.2
mid-flangeThe fastener's distance from the web's outer face, for and , Figures 10.3 and 10.6
Anti-sag bars0Anti-sag bars in the span holding the free flange, 0 to 4, for Tables 10.1 and 10.2

Cross-section resistance, §6.1

CheckClauseWhat the module does
Tension6.1.2, (6.1) on the gross area
Compression6.1.3, (6.2). A fully effective section takes : the extra (6.3) allows is left out, on the safe side
Bending6.1.4, (6.4) for the sense of ; only where the section is fully effective, §3.2.2(5)
Shear6.1.5, (6.8) from Table 6.1 at the web's
Local transverse forces6.1.7, (6.15a) to (6.15e)The web wherever a support or a load reaches it across a flange, with the bearing stated on the member
Tension with bending6.1.8, (6.23)
Compression with bending6.1.9, (6.25)With from the shift of the effective centroid
Bending, axial force and shear6.1.10, (6.27)Where
Bending with a local force6.1.11, (6.28c)At each support or load read in 6.1.7

Member buckling, §6.2

CheckClauseWhat the module does
Flexural buckling6.2.2About and , on , on Table 6.3's curve: b with lips, c without
Torsional and torsional-flexural buckling6.2.3, (6.33), (6.35)With the shear centre off the centroid. (6.35) holds for , so where they differ the longer is used for both, and the result says so
Lateral-torsional buckling6.2.4, EN 1993-1-1 §6.3.2.2Curve b, , and on the member's own moment diagram, lateral restraints and load height: from the table where the diagram is on a row, else the eigenvalue, as on EN 1993-1-1
Bending and axial compression6.2.5, (6.36)The moment includes . Not on a purlin, which §10 verifies instead

Purlins held by sheeting, §10.1

State Sheeting on and the member is a purlin: the sheeting holds one flange laterally and the other flange, the free one, is checked as a beam on an elastic foundation.

  • Does the sheeting hold the flange? With Sheeting S stated, by (10.1a) on each span. If S falls short, the member is not verified. With no S, the sheeting is taken as holding the flange, §10.1.1(6), and the result says that (10.1a) was not checked.
  • The free flange's spring. from by §10.1.5.2. With no the free flange has no spring, , and the result says so.
  • The spans. The member is split at its supports. A span is simple, an end span or an intermediate span, and it is continuous over a support only where a collinear member carries it on without a hinge there.
  • Gravity and uplift. From the moment in each span: (10.3a) on the held flange, (10.3b) on the free one with its lateral moment from (Figure 10.3) and Table 10.1. Where Figure 10.3 leaves a direction open, the safe side is taken.
  • The free flange in compression, by (10.7), with from Tables 10.2a (gravity) and 10.2b (uplift), (10.9), or (10.10a) in uplift with no anti-sag bar, and on curve b with 0.4 and 0.75. With axial compression, 10.1.4.2(5)'s length applies on every span where it is the longer.
  • The roof-plane load. In a model without the sheeting, and in the purlin are the load in the roof's plane, which the sheeting carries to the supports, §10.1.6(2). It is not checked in the purlin, and the result gives its size so you can design the sheeting's fasteners and the support cleats for it, §10.1.1(7). On a roof steeper than 25° the result asks you to check that the sheeting alone carries the down-slope load.

The result says which span each reading is on, and gives , , , , , and . A purlin outside the and of §10.1.1(1) is read, and said to be read past it. past Table 10.1's 40 is read at 40, which only raises .

Verification

The effective section and the purlin are held to printed examples, each recomputed from its inputs:

ExampleWhat it covers
JRC EUR 27346, lipped channel 150 × 47/41 × 16, 1 mm, S350Bending, distortional buckling Steps 1 to 3, ,
Access Steel SX023a and SX022a, lipped channel 200 × 74/66 × 20.8, 2 mm, S350The same section in compression and in bending
Designers' Guide, Example 13.2, lipped channel 200 × 65 × 1.6Compression, distortional buckling,
A published calculation of a plain channel purlin in uplift, , , , ; the web under a point load by (6.15d)

Where a print leaves out rounded corners that §5.1(3) counts, the check counts them, and the test holds the print's value with that factor.

Not covered

Each of these is refused with a message, and the member reads not verified, or is said on the result and left to you:

  • Torsion. EN 1993-1-3 reads it on stresses, (6.11), which are not covered: refused.
  • Bending about the minor axis and shear along y, other than the moment, on a member that is not a sheeted purlin: refused.
  • A plain C whose effective centroid moves towards the web under compression. then compresses the lips' side, whose resistance needs the edge stiffeners under a stress gradient: not verified in compression.
  • A purlin that overhangs a support, and a span not under a uniform load: Tables 10.1 and 10.2 have no row for them, so the purlin is not verified.
  • A compressed free flange with past 200, where Table 10.2 ends: not verified.
  • Lateral-torsional buckling with no warping constant or no unbraced length: not verified in bending.
  • Two opposed local forces closer than , (6.15f) and (6.15g): each is read on its own, and the result asks you to check the pair. A web past = 200 or = 6 has no local-force check, and the result says so. With unstated, (6.15) takes it as 0.
  • Continuous purlins: Tables 10.1 and 10.2 assume equal, uniformly loaded spans with no overlaps or sleeves, 10.1.4.2(3). The spans beyond the member are not measured, so check they match.
  • Not in this module: sigma, hat and other sections, built-up members, trapezoidal sheeting, sleeves and overlaps, the simplified purlin design of Annex E, fasteners and connections, and cold-formed members in fire.

Steel — EN 1993-1-1 for buckling lengths, and the load height; Steel in fire; Sections and materials for the section editor.

Something wrong or unclear on this page? Tell us, and it gets corrected.