Section cuts
A line drawn across a slab, the plate result charted along it, and the moment, shear or normal force the line carries, integrated over its length.
Results & reports 12 min read
A section cut is a straight line drawn across a slab. Along it, Elementarium plots the plate result shown in the viewer, charts it against the distance along the line, and, when the plotted component acts across the line, integrates it into the moment, shear or normal force the section carries. It answers the questions a contour cannot: what the moment is along a support line, and what the strip between two columns carries in total.
A cut is a reading of the results. Drawing, moving or deleting one never changes the model and never asks for a new solve.
What a cut reads
A cut belongs to the slab it was started on, its host plate. Its two ends are stored in that plate's own axes, measured from the plate's centre, so moving or turning the slab takes the cut with it. Deleting the host plate deletes its cuts.
The line is not limited to the host. It reads every plate that lies in the same plane, within 1 mm, so a floor split into bays is one cut. Where the line leaves the slab, crosses an opening or a gap between plates, the diagram stops and starts again past it. It does not bridge the gap.
Each value is read off the meshed field, interpolated inside the element exactly as the contour colours it, so the ordinate at a point is the colour under it. Every element the line crosses is read at both ends of the crossing and at three points between. Where the line passes from one element to the next, both values are kept: at a junction between two plates they differ, and the diagram draws the difference as a step rather than averaging it away.
Drawing a cut
- Arm the tool: Results › Probes › Cut, or Draw a cut in the toolbar of the Cuts panel. It is greyed out in a read-only model, such as an example.
- Click a slab where the cut starts. The point snaps like any other point, and also to the ends of the cuts already drawn.
- Click where it ends. The end lies in the host plate's plane, and the line shows its diagram live while you move. Hold Shift to keep the line on the plate's result or axis, whichever is closer. Shift bends only a free end; a snapped end stays where it snapped. Esc starts over.
The tool stays armed, so the next two clicks draw the next cut. Cuts are named SC1,
SC2, … in the order they are drawn. A new cut becomes the one the Cuts panel
charts.
Snapping uses the object snap and its switch. Once the start is placed, only points on plates in the host's plane are accepted: a point on another floor is not somewhere this cut can end.
What it plots
A cut plots the quantity its viewer is showing, as far as a slab carries it:
| Family | Quantities |
|---|---|
| Moments | , , , , |
| Shear | , |
| Membrane forces | , , , , |
| Displacement | , , , , and in a viewer the rotations , , |
Displacements are in global axes. Member forces, utilisation and the error estimate mean nothing along a line on a slab, and face stresses (σ, τ) are not read along a cut either: under any of these the line is drawn without a diagram.
In a 3D viewer the diagram stands on the line, hatched like a member diagram, at one scale for every cut in the view. Plate resultants hang on the side of the plate's result , so a sagging moment hangs below a floor, on its tension side. A displacement is drawn the way the slab moves. When the viewer draws the deformed shape, the diagram follows it. The diagram is drawn through the slab, so one hanging below a floor stays visible.
Hover the line to read the distance from the start and the value there; at a step, both values are given. The run-end values and the cut's maximum and minimum are written on the diagram when the viewer's Nodal values and Each member's max & min switches are on. Cuts are shown with the Query points switch in the viewer's Display sheet, and always while the tool is armed.
Plate axes or cut axes
Axes decides which axes a cut reads plate results in:
- Plate axes x, y, the default. The diagram reads exactly the number the contour shows under it.
- Cut axes n, t: normal to the line, along it. becomes , the moment transmitted across the line, becomes , becomes , and likewise for and .
With the angle of from the plate's axis:
The membrane forces turn as the moments do. Principal values do not depend on the axes and are unchanged. The normal points towards , or towards for a line along , so it does not flip with the direction the line was drawn in: a cut along reports , and one along reports .
Set the axes in the cut's properties, or in the Cuts panel toolbar when a plate quantity is plotted.
What the line carries
When the plotted component acts on the cut's own face, the Cuts panel integrates it along the line:
is the part of the line that lies on plate; openings and gaps add nothing. The result is labelled Moment across the cut, Shear across the cut or Normal force across the cut, in kNm or kN, not per metre. It is the total over the drawn length: to read what a design strip carries, draw the cut across the strip's width.
The integral is given only where it is a force:
| Axes | Integrated |
|---|---|
| Cut axes | , , , at any angle |
| Plate axes, cut along | , , |
| Plate axes, cut along | , , |
A component along the line, a twisting moment, a principal value, a displacement, or plate axes on an oblique line sum to a number that is no force, and the panel shows none.
The panel also gives the average over the length on plate, , for any plotted quantity. Each element crossing is integrated by Simpson's rule over its five readings.
The Cuts panel
The Cuts panel lists every cut on the left, with its length, and charts the one in focus: the value against the distance along the line, at the cut's full length, with steps at junctions and gaps where the line is off the slab. Above the chart: max and min with their positions, avg over the length on plate, and the integral when there is one. Pointing at the chart marks the station on the line in every viewer, and pointing at the line moves the chart's cursor.
Open it with Open in the Cuts panel in a cut's properties, or with + on a dock's tab strip. The toolbar holds:
- Quantity: As in viewer, the default, follows the viewer the cuts were last looked at in; or pin a moment, shear, membrane force or displacement for this panel.
- Axes, as above.
- The load state, pinned like any other result table.
- Export the diagram to PDF, and Export for the stations as a table.
Moment diagrams are drawn positive downwards, on the tension side, as in the viewer. Shear, membrane forces and displacements are drawn positive upwards.
Selecting and editing a cut
A cut is an object like any other. Click its line to select it; Shift adds to the selection, Ctrl (⌘ on a Mac) toggles. A double click opens its properties. Delete removes the selection. Clicking a row in the Cuts panel selects that cut too, and the panel follows the cut selected anywhere.
| Section | Field | What it does |
|---|---|---|
| General | ID, Label | The id is fixed; a label replaces it as the cut's name |
| On | The host plate; click to select it | |
| Length | Read only | |
| Position | Start u, Start v, End u, End v | The two ends in the host plate's own axes, from its centre |
| Results | Axes | Plate axes x, y or Cut axes n, t |
| Chart | Open in the Cuts panel |
A cut is moved by typing its ends; the line cannot be dragged. In the Cuts panel, double-click a name to rename it, or use the bin on its row to delete it.
Load cases, combinations and envelopes
A cut follows its viewer's load case, combination or envelope, and the Cuts panel follows the ribbon until its own load state is pinned. Under an envelope, a cut reads the envelope's extreme state: at each point, whichever bound is larger in magnitude. It draws one curve, not the two bounds.
Smoothing
A cut reads the same plate field as the contour. With smoothing regions or the project's peak smoothing rule in force, the Cuts panel and the diagram export read the smoothed field. In a viewer, a cut follows the viewer's Smoothed peaks switch, so with the switch off the diagram in that viewer is raw while the panel's chart stays smoothed. With no smoothing set, there is no difference.
Exporting
Export the diagram to PDF in the Cuts panel opens Export diagrams on the focused cut. The same dialog opens from Results › Output › Diagrams and File › Export › Diagrams (PDF)…; those start from the selected members, and All cuts (…) adds every cut in the model. Members and cuts can go in one document.
For a cut you choose the components, out of , , , , , , , , and one load state. Each cut is one figure, its components stacked over one length axis, titled with the cut, the plates it crosses, its axes and its length. The load state, the analysis and the sign convention are stated once at the top. The figures are vector drawings. The integral is not printed on the sheet; read it in the panel.
Download PDF or Print; Download Word writes an editable .docx. Export
diagrams needs Pro, for the PDF and the Word file alike.
Export in the panel writes the focused cut's stations as a table: , X, Y, Z, plate and element, all twelve plate resultants in the axes the cut is set to, and the three translations, with both values at every step. Excel (.xlsx) and CSV (.csv) need Pro; Copy to clipboard works on every plan. See Plans & limits.
Saved with the project
Cuts are part of the project. They are saved with it, travel in the project file, and appear for everyone working on a shared project.
They are not written to IFC or SAF, and the calculation report does not include them. To put a cut in a calculation package, export its diagram and attach it.
Query points
A query point pins a reading to the model instead of to the cursor. Results › Probes › Query point, then click a member or a slab where you want the reading. The point snaps like any other, and on a member also to its quarter points and to the plotted diagram's peaks and zero crossings. A query point on a member is held at a position along it, stated as Along the member (x/L), From the start or From the end, so it stays at "400 mm from the end" when the span changes. One on a slab is held in the plate's own axes, like a cut's ends.
A query point reports every component at its point, not only the one plotted: forces and
displacements on a member, the plate resultants on a slab. The Query points table
lists them all for the ribbon's load state, and is where a position can be typed. In a
query point's properties, Across cases compares it over every load case and
combination; click a bar to switch the results to that case. Query points are named Q1,
Q2, …, are saved with the project, and are not written to IFC.
Limits
- Straight lines in one plane. A cut has two ends. It cannot turn a corner onto a wall, or follow a curved shell: of a shell built from flat plates, it reads only the plates in its host's plane.
- Along an element edge, a cut reads the elements on one side of the edge only. To read a support line along a wall from a chosen side, draw the cut slightly off the edge.
- 3D viewers only. Cuts are not drawn in a 2D viewer.
- No design strip. The integral is over the drawn line, with no strip width, column-strip and middle-strip split, or design to EN 1992.
- No stresses. Face stresses are not plotted along a cut.
- The mesh sets the resolution. A cut does not refine the mesh; the diagram has five readings per element crossed.
- Not in the report, IFC or SAF, as above.
Something wrong or unclear on this page? Tell us, and it gets corrected.